Head Mount Temperature Transmitter with TC Input, Current Output, Intrinsically Safe - DAT 1015 IS

(No reviews yet) Write a Review
DAT 1015 IS
50.00 Grams
Minimum Purchase:
1 unit


Datexel Intrinsically safe two wire transmitter - DAT 1015 IS

Intrinsically safe, Thermocouple compatible, Highly accurate

The transmitter DAT 1015 IS is able to execute many functions such as: measure and linearisation of the temperature characteristic of RTDs sensors, conversion of a linear resistance variation, conversion of a voltage signal even coming from a potentiometer connected on its input. Moreover, the DAT 1015 IS is able to measure and linearise the standard thermocouples with internal cold junction compensation. The measured values are converted in a 4÷20 mA current signal. The device guarantees high accuracy and performances stability both in time and in temperature.

The programming of the DAT 1015 IS is made by a Personal Computer using the software PROSOFT, developed by DATEXEL, that runs under the operative system "WindowsTM ". By use of PROSOFT, it is possible to configure the transmitter to interface it with the most used sensors.

In case of sensors with a no-standard output characteristic, it is possible to execute, via software, a "Custom" linearisation (per step) to obtain an output linearise signal. For Resistance and RTDs sensors it is possible to program the cable compensation with 3 or 4 wires; for Thermocouples it is possible to program the Cold Junction Compensation (CJC) as internal or external.

It is possible to set the minimum and maximum values of input and output ranges in any point of the scale, keeping the minimum span shown in the table below.

Moreover, it is available the option of alarm for signal interruption (burn-out) that allows to set the output value as high or low out of scale.

It is housed in a self-extinguish plastic enclosure suitable for DIN B in-head mounting.


DAT1015 IS Datexel has the following advantages:

  • PROTECTION MODE: II 1 G Ex ia IIC T6, T5, T4 Ga certified in according to the Directive ATEX 014/34/EU
  • Applicable in zones with explosion risk (ZONE 0)
  • Configurable input for RTD, mV, Tc, Resistance and Potentiometer
  • 4 ÷ 20 mA configurable output on current loop
  • Configurable by Personal Computer, on-field reconfigurable
  • High accuracy
  • EMC compliant – CE mark
  • Suitable for DIN B in-head mounting


Input type for Datexel DAT 1015 IS

Input for this model is as follows:


  • Thermocouple: J, K, S, R, B, E, T, N
  • RTD: 2,3,4 wires, Pt100, Pt1000, Ni100, Ni1000
  • Voltage: mV
  • Potentiometer
  • RES. 2,3,4 wires


Output type

Output for this temperature transmitter is:

  • Direct Current: 4 mA … 20 mA
  • Reverse Current: 20 mA … 4 mA


Response time

The response time for this transmitter is about 400 ms.


Power supply

power supply voltage for DAT 1015 IS is the standard 11 to 30 VDC. Also Reverse polarity protection is 60 VDC max.


Temperature & humidity Consideration

  • Operative temperature -20°C ... +70°C
  • Storage temperature -40°C ... +85°C
  • Humidity (not condensed) 0 ... 90 %



  • Material: Self-extinguish plastic
  • Mounting: DIN B head or bigger
  • Weight: about 50 g.



  • Furnace
  • Oil and gas
  • Brick manufacturing
  • Heat Exchangers
  • Industrial Processes
  • Heating/cooling systems

Series Information

“DAT1000 SERIES”: temperature transmitters for DIN B in-head mounting

The transmitters of the DAT1000 series can accept at their input signals coming from 2,3 or 4 wires Pt100, thermocouple and potentiometer sensors or voltage signals (mV).The devices provide a 4÷20 mA two wire current loop output signal.

The series is composed of devices with input configurable by PC with or without galvanic isolation. Moreover, it is available a version of the transmitters of the DAT1000 series developed for the use in potentially explosive atmospheres certified in according to the DIRECTIVE ATEX 94/9/EC. (see p. 24 to 26).

  • DAT 1010: Two wire transmitter for RTD programmable by PC
  • DAT 1015: Two wire universal transmitter programmable by PC
  • DAT 1061: Isolated two wire Transmitter for RTD programmable by PC
  • DAT 1066: Isolated two wire universal transmitter programmable by PC


About Datexel:

Founded in 1992 from the commitment and aspiration of several partners as a small provincial company, through the years DATEXEL has become an established reality on Italian and international markets as a manufacturer of electronic equipment for industrial automation and control process.

The range of DATEXEL products includes: Transmitters, signal and temperature Converters (both analogue and digital), galvanic Isolators, signal Splitters, I/O Modules, Trip Amplifiers, Power Supply Units, current loop Isolators, analogue and digital Displays.

Datexel Products are used in following industries:

  • Steel production
  • Automotive
  • Oil and gas
  • Shipbuilding



To View Data Sheet for Temperature Transmitter For Explosive & Safe Environment DAT1015IS Please Click Here
View AllClose

Warranty Information

One Year Warranty.
View AllClose

Additional Information

Input signal type:
TC (J, k, S, R, B, E, T, N), RTD (PT100, PT1000, Ni100, Ni1000), Voltage (mV), Potentiometer, RES. 2,3,4 wires
Output type DC:
Min. 4mA. Max. 20mA.
Output type Reverse Current:
Min. 20mA. Max. 4mA.
Response time (10÷ 90%):
About 400 ms.
Power supply:
Power supply voltage 11…30 Vdc. Reverse polarity protection 60 Vdc max.
Temp. and humidity:
Operative temperature -20°C …+70°C, 'HT' vers: -20°C …+85°C. Storage temperature -40°C …+85°C Humidity (not condensed) 0 .. 90 %
Material PC + ABS V0. Mounting DIN B head or bigger. Weight about 50 g. Dimensions Ø= 43 mm ; H = 24 mm
EMC (for industrial environments):
Immunity EN 61000-6-2. Emission EN 61000-6-4.
View AllClose