Temperature Transmitter DAT1010

(No reviews yet) Write a Review
SKU:
DAT1010
MPN:
DAT1010
Weight:
500.00 Grams
Minimum Purchase:
1 unit
Shipping:
Calculated at Checkout
$77.00

Description

DAT1010 from Datexel is an RTD Head Mounted Temperature transmitter or sometimes called a Hockey puck Temperature Transmitter. It can accept signals from RTD's, mV, Resistance, and Potentiometer and convert the signal into a 4-20mA signal. The DAT1010 "in head Mounted Temperature Transmitter" is PC Programmable. The sensor type, range, zeros and linearization are programmable with the Prodat software and the CVPROG programming cable, available from DATEXEL.
The sensor is connected to the input terminals and with the use of a high impedance measuring circuit the signal is ascertained. It is then linearized if needed and converted and scaled to the industrial standard of 4-20mA signal (2 Wire device).
The options for the RTD sensor are 2, 3, or 4 wire sensors and can be configured for Pt100, Pt1000, Ni100 or Ni1000 RTD's.
The resistance input range is selectable from 0-200, 0-500, 0-2000 Ω, and for Potentiometers the range of 200 Ω, 500 Ω; or 50K Ω selectable.
The DAT1010 can also accept inputs from mV sensors from the range of -100mV to 700mV with a minimum span of 2 mV.
It is recommended with an RTD input, to use a 3 or 4 wire RTD. This dramatically improves the accuracy of the circuit. There is an option to program the burn out failure alarm on the 4-20mA signal to High (20mA) or Low (4mA) and there is a damping function. The power supply to the Temperature Transmitter has a high range of tolerance and can accept a voltage between 10 and 32 Volt. The DAT1010 Temperature-Transmitter is Loop Powered (2 Wire).

 

DAT1010 from Datexel comes with the following features:

  • Configurable input for RTD, mV, Resistance, and Potentiometer.
  • Damping function on output.
  • 4 ÷ 20 mA configurable output on the current loop.
  • Configurable by Personal Computer.
  • High accuracy.
  • On-field reconfigurable.
  • Configurable by interface PRODAT05 or PRODAT-06 without the power loop connected.
  • EMC compliant with CE mark.
  • Suitable for DIN B in-head mounting.
  • Option for DIN rail mounting in compliance with EN 50022 (DIN RAIL Option).

Product Specification

Features

Range/Description

Input

  • Input signal type

RTD, Potentiometer, Voltage, Resistance.

  • Input calibration

RTD > of ±0.1% f.s. or ±0.2°C.

Low res. > of ±0.1% f.s. or ±0.15 Ω.

High res. > of ±0.2% f.s. or ±1 Ω. mV > of ±0.1% f.s. or ±18 uV.

  • Input impedance

mV >= 10 MΩ.

Output

  • Output type DC

Min. 4mA.

Max. 20mA.

  • Output type Reverse Current

Min. 20mA.

Max. 4mA.

  • Output calibration

Current ± 7 uA.

  • Linearity

RTD ± 0.1 % f.s.

  • Line resistance influence

mV <=0.8 uV/Ohm.

RTD 3 wires 0.05%/Ω (50Ω balanced max.).

RTD 4 wires 0.005%/ Ω (100Ω balanced max.).

  • RTD excitation current

Typical 0.350 mA.

  • Thermal drift

0.01 % of f.s./°C.

  • Burnout values

Max. output value about 20.5 mA.

Min. output value about 3.8 mA.

Max. fault value about 21.6 mA. Min. fault value about 3.5 mA.

  • Damping time constant

Selectable from 0.3 to 30 s. Value 0: function not active.

  • Response time (10÷ 90%)

About 400 ms.

  • Power supply

Power supply voltage 10…32 Vdc.

Reverse polarity protection 60 Vdc max.

  • Isolation voltage

Input – Power supply 1500 Vac, 50 Hz,1 min.

  • Temp. and humidity

Operative temperature -40°C …+85°C.

Storage temperature -40°C …+85°C.

Humidity (not condensed) 0 …90 %.

  • Housing

Material PC + ABS V0.

Mounting DIN B head or bigger.

Weight about 50 g.

Dimensions Ø= 43 mm ; H = 24 mm

  • EMC (for industrial environments)

Immunity EN 61000-6-2.

Emission EN 61000-6-4.

Brand Information

Datexel products are made to the very highest standards and all products carry the CE mark, and since March 2015 all slim-line products and DAT3000 modules carry the UL and CSA mark. Datexel obtained ISO 9001 in 1996 and now has the current standard UNI EN ISO 9001:2000 (issued in 2001). Datexel's signal conditioners also carry the ATEX 94/9/EC approval for safe environments. In July 2006, Datexel confirmed its products to the RoHS Directive Standard (2002/95/EC) which imposes restrictions on the use of dangerous substances for the manufacturing of electric and electronic equipment. Situated in Jupiter, Florida USA.

Data Sheet

To View Data Sheet Please Click Here
View AllClose

Warranty Information

One Year Warranty.
View AllClose