null

DATEXEL Temperature Transmitter Device In-Head Mounting Temperature Transmitter DAT1010IS

Write a Review
SKU:
DAT1010IS
MPN:
DAT1010IS
Weight:
500.00 Grams
Minimum Purchase:
1 unit
Shipping:
Calculated at Checkout
$133.00

Description

DAT1010IS from Datexel is an Intrinsically Safe RTD Head Mount Temperature Transmitter. The input also accepts mV's, Potentiometers and resistance Inputs. The DAT1010IS "in head Mount Temperature Transmitter" is PC Programmable. The sensor, range, zero and linearization, is programmable with the Prodat software, available from DATEXEL. The input is measured, linearized and converted to the industrial standard of 4-20mA signal. The RTD and resistance input has the added feature of selecting 3 or 4 wire for higher accuracy. There is a burn out failure alarm that can be programmed to drive the output signal High and Low. The input on the DAT1010IS has a high range of tolerance and the DAT1010IS can accept any a voltage between 11 V and 30 Volt. The power is Loop Powered.

The DAT1010IS is accurate to 0.1% full scale mV Linear and has less than 0.02%/°f thermal drift. It is in compliance with the standard 89/336/CEE on the Electromagnetic Compatibility and is housed in a self-extinguish plastic enclosure suitable for DIN B in-head mounting. There is a mounting kit available to mount the DAT1010IS on DIN rail.

DAT1010IS from Datexel comes with the following features:

  • PROTECTION MODE: II 1 G Ex ia IIC T6,T5,T4 Ga certified in according to the Directive ATEX 2014/34/EU.
  • Applicable in zones with explosion risk (ZONE 0).
  • Configurable input for RTD, mV, Resistance, and Potentiometer.
  • 4 ÷ 20 mA configurable output on the current loop.
  • Configurable by Personal Computer, on-field reconfigurable.
  • High accuracy.
  • EMC compliant with CE mark.
  • Suitable for DIN B in-head mounting.

Brand Information

Datexel products are made to the very highest standards and all products carry the CE mark, and since March 2015 all slim-line products and DAT3000 modules carry the UL and CSA mark. Datexel obtained ISO 9001 in 1996 and now has the current standard UNI EN ISO 9001:2000 (issued in 2001). Datexel's signal conditioners also carry the ATEX 94/9/EC approval for safe environments. In July 2006, Datexel confirmed its products to the RoHS Directive Standard (2002/95/EC) which imposes restrictions on the use of dangerous substances for the manufacturing of electric and electronic equipment. Situated in Jupiter, Florida USA.

Data Sheet

To View Data Sheet Please Click Here
View AllClose

Warranty Information

One Year Warranty.
View AllClose

Additional Information

Input:
none
Input signal type:
RTD, Potentiometer, Voltage, Resistance.
Input calibration:
RTD > of ±0.1% f.s. or ±0.2°C. Low res. > of ±0.1% f.s. or ±0.15 Ω. High res. > of ±0.2% f.s. or ±1 Ω. mV > of ±0.1% f.s. or ±18 uV.
Input impedance:
mV >= 10 MΩ.
Output:
none
Output type DC:
Min. 4mA. Max. 20mA.
Output type Reverse Current:
Min. 20mA. Max. 4mA.
Output calibration:
Current ± 7 uA.
Linearity:
RTD ± 0.1 % f.s.
Line resistance influence:
mV <=0.8 uV/Ohm. RTD 3 wires 0.05%/Ω (50Ω balanced max.). RTD 4 wires 0.005%/ Ω (100Ω balanced max.).
RTD excitation current:
Typical 0.350 mA.
Thermal drift:
0.01 % of f.s./°C.
Burnout values:
Max. value about 22.5 mA. Min. value about 3.6 mA.
Response time (10÷ 90%):
About 400 ms.
Power supply:
Power supply voltage 10…32 Vdc. Reverse polarity protection 60 Vdc max.
Isolation voltage:
Input – Power supply 1500 Vac, 50 Hz,1 min.
Temp. and humidity:
Operative temperature -20°C …+70°C, 'HT' vers: -20°C …+85°C. Storage temperature -40°C …+85°C Humidity (not condensed) 0 .. 90 %
Housing:
Material PC + ABS V0. Mounting DIN B head or bigger. Weight about 50 g. Dimensions Ø= 43 mm ; H = 24 mm
EMC (for industrial environments):
Immunity EN 61000-6-2. Emission EN 61000-6-4.
View AllClose