DAT4135-SEL Temperature Transmitter

(No reviews yet) Write a Review
SKU:
DAT4135-SEL
Weight:
40.00 Grams
Shipping:
Calculated at Checkout
$307.00

Description

DAT4135-SELfrom Datexel is a DIN Rail mount signal transmitter with PC programmability. The input is Universal and can be thermocouples, RTD, mA, V, mV, Resistor.nce and potentiometer. The DAT4135 will linearize the input and provide a 4-20mA or voltage output signal. The DAT4135 is accurate to 0.1% full scale and has less than 0.01%/°f thermal drift. The DAT4135 is programmable by PC based software which has been developed by DATEXEL to be user-friendly.
For resistance and RTD's sensors, it is possible to program the cable compensation for 3 or 4 wires.
It is possible to set the minimum and maximum values of the input and output range at any point of the scale, keeping the minimum span shown in the Data-sheet. Also, a high burn out alarm or low burn out alarm is selectable.
The DAT4135 is isolated between the input and the power supply/output to 2000V, eliminates the effects of any ground loops and allows the use of the transmitter in heavy environmental conditions found in industrial applications. The DAT4135 is In compliance with the standard 89/336/CEE on the Electromagnetic Compatibility. The DAT4135 is housed in a plastic enclosure of 12.5 mm thickness suitable for DIN rail mounting in compliance with EN-50022 and EN-50035 standards.
The DAT4135 is able to measure and linearize the standard thermocouples with internal cold junction compensation.  

 

DAT4135-SEL from Datexel comes with the following features:

  • Configurable input for RTD, TC, mV, V, mA, Resistor.nce and Potentiometer.
  • Galvanic isolation at 2000 Vac.
  • Configurable output in current or voltage.
  • Configurable by Personal Computer.
  • High accuracy.
  • On-field reconfigurable.
  • EMC compliant with CE mark.
  • Suitable for DIN rail mounting in compliance with EN-50022 and EN50035

Product Specification

Features

Range/Description

Input Calibration

  • RTD

> of ±0.1% f.s. or ±0.2°C.

  • Low Resistor.nce

> of ±0.1% f.s. or ±0.15 Ω.

  • High Resistor.nce

> of ±0.2% f.s. or ±1 Ω.

  • mV, TC

> of ±0.1% f.s. or ±18 uV.

  • Volt

> of ±0.1% f.s. or ± 2 mV.

  • mA

> of ±0.1% f.s. or ± 6 uA.

Output Calibration

  • current

± 7 uA.

  • voltage

± 5 mV.

Input impedance

  • TC mV

>= 10 MΩ.

  • Volt

>= 1 MΩ.

  • Current

~ 50 Ω.

Linearity

  • TC

± 0.2 % f.s.

  • RTD

± 0.1 % f.s.

Line Resistor.nce influence

  • TC, mV

<=0.4 uV/Ohm.

  • RTD 3-wired

0.05%/Ω (50 Ω balanced max.).

  • RTD 4-wired

0.005%/Ω (100 Ω balanced max.).

  • RTD excitation current (typical)

0.350 mA.

  • CJC comp.

± 0.5°C.

Thermal Drift 1

  • Full Scale

± 0.01% / °C.

  • CJC

± 0.01% / °C.

Burnout values

  • Max. value

About 22.5 mA.

  • Min. value

About 3.6 mA.

  • Response time (10÷ 90%)

About 400ms.

Power supply

  • Power supply voltage

18…32VDC.

  • Reverse polarity protection

60VDC max.

Current consumption

  • Current output

40mA max.

  • Voltage output

20mA max.

Output load Resistor.nce

  • Current output

≤ 650 Ω.

  • Voltage output

≥ 3.5 KΩ.

  • Limitation current

About 25 mA.

Isolation

  • Input-power supply output

2000 Vac, 50 Hz,1 min.

Environmental conditions

  • Operative temperature

-20°C …+70°C.

  • Storage temperature

-40°C…+85°C.

  • Humidity (not condensed)

0 …90 %.

  • Maximum altitude

2000m.

  • Installation

Indoor.

  • Category of installation

II.

  • Pollution Degree

2.

Mechanical specifications

  • Material

Self-extinguish plastic.

  • IP code

IP20.

  • Wiring

Wires with diameter 0.8÷2.1 mm2 /AWG 14-18

  • Tightening torque

0.8 Nm.

  • Mounting

In compliance with DIN rail standard EN-50022 and EN-50035

  • Weight

About 90g.

EMC (for industrial environments)

  • Immunity

EN 61000-6-2.

  • Emission

EN 61000-6-4.

Brand Information

Datexel products are made to the very highest standards and all products carry the CE mark, and since March 2015 all slim-line products and DAT3000 modules carry the UL and CSA mark. Datexel obtained ISO 9001 in 1996 and now has the current standard UNI EN ISO 9001:2000 (issued in 2001). Datexel's signal conditioners also carry the ATEX 94/9/EC approval for safe environments. In July 2006, Datexel confirmed its products to the RoHS Directive Standard (2002/95/EC) which imposes restrictions on the use of dangerous substances for the manufacturing of electric and electronic equipment. Situated in Jupiter, Florida USA.

Data Sheet

To View Data Sheet Please Click Here
View AllClose

Warranty Information

One Year Warranty.
View AllClose