DATEXEL Temperature Transmitter Device In-Head Mounting Temperature Transmitter DAT1135

Write a Review
500.00 Grams
Minimum Purchase:
1 unit
Calculated at Checkout


DAT1135 from Datexel is a Thermocouple Head Mounted Temperature converter. The output is 0-10 volts with the minimum span being 1 V, so all the standard outputs are possible, 0-10V, 1-5V and 2-10V. The input accepts Thermocouples, RTD's, mV's, Potentiometers and resistance inputs. The DAT1135 is programmable by a PC using the Prodat and the DATASOFT software. The sensor, range, zero and linearization are programmable. The input is measured, linearized and converted to the industrial standard. The RTD and resistance input have the added feature of selecting 3 or 4 wire for higher accuracy. There is a burn out failure alarm that can be programmed to drive the output signal High and Low.

The input on the DAT1135 has a high range of tolerance and the DAT1135 can accept any a voltage between 10 V and 32 V. The thermocouple selection type is J, K, S, R, B, E, T and N. The RTD sensor is selectable for Pt100, Pt1000, Ni100 or Ni1000. The resistance input is selectable from 0-200, 0-500, 0-2000 Ohms. The mV input is selectable from -100mV to 700mV with a minimum span of 2 mV. The Potentiometer can accept resistance in the range of 0-200 Ohms, 200-500 Ohms and 0.5 to 2 K ohms. The RTD and resistance can be 2 wire or use compensation wire to improve accuracy i.e. 3 or 4 wire.

DAT1135 from Datexel comes with the following features:

  • Configurable input for RTD, TC, mV, Resistance, and Potentiometer.
  • Galvanic isolation at 1500 Vac.
  • Voltage output configurable from 0 up to 10 Vdc.
  • Configurable by Personal Computer.
  • Configurable by interface PRODAT05 or PRODAT06 without the power supply connected.
  • High accuracy.
  • On-field reconfigurable.
  • EMC compliant with CE mark.
  • Suitable for DIN B in-head mounting.
  • Option for DIN rail mounting in compliance with EN 50022 (DIN RAIL Option)

Brand Information

Datexel products are made to the very highest standards and all products carry the CE mark, and since March 2015 all slim-line products and DAT3000 modules carry the UL and CSA mark. Datexel obtained ISO 9001 in 1996 and now has the current standard UNI EN ISO 9001:2000 (issued in 2001). Datexel's signal conditioners also carry the ATEX 94/9/EC approval for safe environments. In July 2006, Datexel confirmed its products to the RoHS Directive Standard (2002/95/EC) which imposes restrictions on the use of dangerous substances for the manufacturing of electric and electronic equipment. Situated in Jupiter, Florida USA.

Data Sheet

To View Data Sheet Please Click Here
View AllClose

Warranty Information

One Year Warranty.
View AllClose

Additional Information

Input signal type:
RTD, Potentiometer, Voltage, Resistance.
Input calibration:
RTD > of ±0.1% f.s. or ±0.2°C. Low res. > of ±0.1% f.s. or ±0.15 Ω. High res. > of ±0.2% f.s. or ±1 Ω. TC, mV > of ±0.1% f.s. or ±10 uV.
Input impedance:
mV >= 10 MΩ.
Output type Direct Voltage:
Min. 0V. Max. 10V.
Output type Reverse Voltage:
Min. 10V. Max. 0V.
Output calibration:
Voltage ± 5 mV.
Output load resistance:
Voltage output ≥ 5 KΩ. Short-circuit current 26 mA max.
Output filter programmability:
Selectable from 0.2 to 30 s.
TC ± 0.2 % f.s. RTD ± 0.1 % f.s.
Line resistance influence:
TC, mV <=0.8 uV/Ohm. RTD 3 wires 0.05%/Ω (50Ω balanced max.). RTD 4 wires 0.005%/ Ω (100Ω balanced max.).
RTD excitation current:
Typical 0.350 mA.
CJC comp.:
± 0.5°C.
Thermal drift:
Full scale ± 0.01% / °C. CJC ± 0.01% / °C.
Burnout values:
Max. Fault value about 11.1 V. Min. Fault value about -0.65 V.
Response time (10÷ 90%):
About 200 ms.
Power supply:
Power supply voltage 18 …30 Vdc. Current consumption 10 mA max. Reverse polarity protection 60 Vdc max.
Isolation voltage:
Input – Pow. supply/Output 1500 Vac, 50 Hz,1min.
Temp. and humidity:
Operative temperature -40°C …+85°C. Storage temperature -40°C …+85°C. Humidity (not condensed) 0 …90 %.
Material PC + ABS V0. Mounting DIN B head or bigger. Weight about 50 g. Dimensions Ø= 43 mm ; H = 24 mm
EMC (for industrial environments):
Immunity EN 61000-6-2. Emission EN 61000-6-4.
View AllClose