Datexel Isolated Module Modbus Data Acquisition with Data logger for SD Ram - DAT9011-DL-2.0

EMC / CE mark, N°1 Slot for micro SD card, Suitable for DIN rail mounting – made in Italy

The device DAT9011DL is an Intelligent unit able to control a network of slave Modbus RTU devices connected on serial line RS-485 Master or Modbus TCP through the Ethernet interface executing the reading and writing of the field values and performing the logical and mathematical functions necessary for the system working, managing up to 10 task of recording memorized on files saved on the SD card memory.

It is possible to get access to the saved files by means of the Ethernet connection.

The device is equipped with one universal analogue input channel, one channel for Volt and mA input, two digital inputs with 32-bit pulse counters and 2 relay outputs.

On input an Auxiliary source is available to supply passive sensors on the field. By means of the Ethernet interface or the RS-485 “SLAVE” or uUSB ports it is possible to read and write, in real time, the internal registers value.

Moreover, by means of the Ethernet interface or by the RS-485 “SLAVE” or uUSB ports it is possible to program the Control Logic, to request data and programming in real time the device, to program directly the slave devices connected on the RS-485 Master and to request data from them.

The device DAT9011DL is configurable by the software DEV9K 2.0 and successive versions developed by DATEXEL and running under Windows. The LED of signaling of Ethernet activity and data Rx-Tx flow on the serial line allows a direct monitoring of the system functionality. The connection is made by removable screw-terminals (supply and RS-485) and RJ45 plug (Ethernet). The device DAT9011DL realizes a full electrical isolation between the lines, introducing a valid protection against the effects of all ground loops eventually existing in industrial applications. The device is housed in a rough self-extinguishing plastic enclosure which, thanks to its thin profile of 22.5 mm only, allows a high density mounting on EN-50022 standard DIN rail.

The advantages and features for Datexel Isolated Module DAT9011-DL-2.0:

• N°1 serial interface RS-485 Modbus RTU Master
• N.1 serial interface RS-485/uUSB Modbus RTU Slave
• N°1 Slot for microSD card
• Interface Ethernet 10/100 Base-T, Modbus TCP Client/Server
• N°1 universal analogue input + N°1 current and voltage analogue input
• N°2 digital Inputs with 32 bit pulse counters + N°2 SPDT Relay Outputs
• Auxiliary supply to power sensors on field
• N°2 passive 4-20 mA analogue outputs
• Master both on RS-485 (Modbus RTU) and on Ethernet (Modbus TCP)
• Programming software with "flow chart" structure
• Remotely programmable
• Connection by removable screw-terminals
• LED signaling for Link/Act Ethernet, serial RX-TX, power supply and digital inputs/outputs
• Programmable without external sources via uUSB and CVPROG cable
• Galvanic Isolation on all the ways
• EMC compliance – CE mark
• Suitable for DIN rail mounting in compliance with EN-50022 standard

Input for Datexel Isolated Module DAT9011-DL-2.0

• Voltage (mV, V)
• Thermocouple (J, K, S, R, B, E, T, N)
• RTD (*) 2,3 wires Pt100, Pt1000, Ni100, Ni1000
• Potentiometer
• RES. 2,3 wires
• Current

Output

• Current 4 mA 20

DIGITAL INPUTS

• Number of Channels 2
• Input voltage OFF State : 0÷3 V
• (bipolar) ON State : 10÷30 V
• Input Impedance 4.7 Kohm
• N°2 Digital counter 32 bit (up to 5 kHz)

DIGITAL OUTPUTS

• N.2 Relays SPDT
• SD card and datalogger
• Type microSD (SDHC)
• Memory size Up to 32 GB
• Format FAT16 or FAT32
• N° Logging task up to 10
• Min. schedule rate 10 seconds

Serial Ports RS-485 (Master & Slave)

In compliance with EIA 485

• Protocol Modbus RTU
• Baud Rate up to 115.2 kbps

POWER SUPPLY

• Supply voltage 9 ÷ 30 Vdc
• Current cons. @ 24 V 60 mA (170 mA max)
• Current cons. @ 10 V 147 mA (300 mA max)
• Polarity rev. protection 60 Vdc max.

ISOLATION

• 1500 Vac, 50 Hz, 1 min

ENVIRONMENTAL CONDITIONS

• Operative Temperature -20°C .. +60°C
• Storage Temperature -40°C.. +85°C
• Humidity (not condensed) 0 .. 90 %
• Maximum Altitude 2000 m
• Installation Indoor
• Category of installation II
• Pollution Degree 2

MECHANICAL SPECIFICATIONS

• Material Self-extinguish plastic
• IP Code IP20
• Wiring wires with diameter 0.8÷2.1 mm2 /AWG 14-18
• Tightening Torque 0.5 N m
• Mounting in compliance with DIN rail standard EN-50022
• Weight about 190 g.

CERTIFICATIONS

• EMC (for industrial environments) Immunity EN 61000-6-2, Emission EN 61000-6-4