null
Datexel

DIN Rail Temperature Transmitter with Thermocouple Input, Current Output - DAT4035

(No reviews yet) Write a Review
SKU:
DAT4035
MPN:
DAT4035
Weight:
90.00 Grams
Minimum Purchase:
1 unit

Description

Datexel PC programmable two wire isolated universal transmitter - DAT4035

TC/RTD/… Input, Current Output, Highly Accurate, Made in Italy

 

The transmitter DAT 4035 is able to execute many functions such as: measure and linearisation of the temperature characteristic of RTDs sensors, conversion of a linear resistance variation, conversion of a standard active current signal, conversion of a voltage signal even coming from a potentiometer connected on its input.

Moreover, the DAT 4035 is able to measure and linearise the standard thermocouples with internal cold junction compensation.

The measured values are converted in a 4-20 mA current signal. The device guarantees high accuracy and performances stability both in time and in temperature.

The programming of the DAT 4035 is made by a Personal Computer using the software PROSOFT, developed by DATEXEL, that runs under the operative system "WindowsTM ". By use of PROSOFT, it is possible to configure the transmitter to interface it with the most used sensors.

In case of sensors with a no-standard output characteristic, it is possible to execute, via software, a "Custom" linearisation (per step) to obtain an output linearise signal.

For Resistance and RTDs sensors it is possible to program the cable compensation with 3 or 4 wires; for Thermocouples it is possible to program the Cold Junction Compensation (CJC) as internal or external.

It is possible to set the minimum and maximum values of input and output ranges in any point of the scale, keeping the minimum span shown in the table below.

Moreover, it is available the option of alarm for signal interruption (burn-out) that allows to set the output value as high or low out of scale.

The terminals of the current signal on input side must be only connected to active current loop.

The 2000 Vac isolation between input and power supply/output eliminates the effects of all ground loops eventually existing and allows the use of the transmitter in heavy environmental conditions found in industrial applications.

It is housed in a plastic enclosure of 12.5 mm thickness suitable for DIN rail mounting in compliance with EN-50022 and EN-50035 standards.

The advantages for temperature transmitter DAT4035:

  • Configurable input for RTD, TC, mV, V, mA, Resistance and Potentiometer
  • Galvanic isolation at 2000 Vac
  • 4 - 20 mA configurable output on current loop
  • Configurable by Personal Computer
  • High accuracy
  • On-field reconfigurable
  • EMC compliant – CE mark
  • Suitable for DIN rail mounting in compliance with EN-50022 and EN50035

Input for DAT4035 temperature transmitter is:

  • TC (*) CJC int./ext.
  1. J -200°C 1200°C 100 °C
  2. K -200°C 1370°C 100 °C
  3. S -50°C 1760°C 400 °C
  4. R -50°C 1760°C 400 °C
  5. B 400°C 1820°C 400 °C
  6. E -200°C 1000°C 100 °C
  7. T -200°C 400°C 100 °C
  8. N -200°C 1300°C 100 °C
  • Current
  1. mA -10 mA +24 mA 2 mA
  2. RES. 2,3,4 wires
  3. Low 0 W 300 W 10 W
  4. High 0 W 2000 W 200 W
  • Potentiometer
  1. (Nominal value) 0 W 200 W 10%
  2. 200 W 500 W 10%
  3. 0.5 KW 50 KW 10%
  • Voltage
  1. mV -400 mV +400 mV 2 mV
  2. mV -100 mV +700 mV 2 mV
  3. Volt - 10 V +10 V 500 mV
  • RTD (*) 2,3,4 wires
  1. Pt100 -200°C 850°C 50°C
  2. Pt1000 -200°C 200°C 50°C
  3. Ni100 -60°C 180°C 50°C
  4. Ni1000 -60°C 150°C 50°C

Output for temperature transmitter DAT4035 is as follows:

  • Direct current 4 mA 20 mA 4 mA
  • Reverse current 20 mA 4 mA 4 mA

POWER SUPPLY

  • Power supply for this temperature transmitter is 10 .. 32 Vdc and the Reverse polarity protection is equal to 60 Vdc max.

ISOLATION

  • Input – Power supply/Out 2000 Vac, 50 Hz,1 min

ENVIRONMENTAL CONDITIONS

These conditions are listed as bellow:

  • Operative Temperature -40°C .. +85°C
  • Storage Temperature -40°C.. +85°C
  • Humidity (not condensed) 0 .. 90 %
  • Maximum Altitude 2000 m
  • Installation Indoor
  • Category of installation II
  • Pollution Degree 2

MECHANICAL SPECIFICATIONS

Material, IP and wiring is as follows:
  • Material Self-extinguish plastic
  • IP Code IP20
  • Wiring wires with diameter 0.8÷2.1 mm2 /AWG 14-18
  • Tightening Torque 0.8 N m
  • Mounting in compliance with DIN rail standard EN-50022 and EN-50035
  • Weight about 90 g.

Industries/applications

  • Furnace
  • Oil and gas
  • Brick manufacturing
  • Heat Exchangers
  • Industrial Processes
  • Heating/cooling systems

Series Information

"SMART SERIES" Temperature and signal transmitters and converters for DIN rail mounting

The SMART series devices can accept on their input several types of signals coming from the field; the series is composed of:

• 4-20 mA two wires isolated Transmitter for universal input (DAT4035)

• Isolated Converters for universal input with configurable output as voltage or current (DAT4135, DAT 4235)

• Isolated Converter for universal input with configurable output as voltage or current and trip amplifier (DAT4520)

About Datexel:

Founded in 1992 from the commitment and aspiration of several partners as a small provincial company, through the years DATEXEL has become an established reality on Italian and international markets as a manufacturer of electronic equipment for industrial automation and control process.

The range of DATEXEL products includes: Transmitters, signal and temperature Converters (both analogue and digital), galvanic Isolators, signal Splitters, I/O Modules, Trip Amplifiers, Power Supply Units, current loop Isolators, analogue and digital Displays.

Documents

You may be interested to see this product's catalog. If so, please click to view the DAT4035 datasheet.
View AllClose

Warranty Information

One Year Warranty.
View AllClose

Additional Information

Input type:
TC, RTD, voltage, potentiometer, resistance, current (details in datasheet)
Input calibration:
RTD > of ±0.1% f.s. or ±0.2°C. Low res. > of ±0.1% f.s. or ±0.15Ω. High res. > of ±0.2% f.s. or ±1 Ω. mV, TC > of ±0.1% f.s. or ±18 uV. Volt > of ±0.1% f.s. or ± 2 mV. mA > of ±0.1% f.s. or ± 6 uA.
Input impedance:
TC, mV >= 10 M Ω. Volt >= 1 M Ω. Current ~ 50 Ω.
Output type DC:
Min: 4mA. Max: 20mA.
Output type Reverse:
current Min: 20mA. Max: 4mA.
Output calibration:
Current ± 7 uA.
Linearity:
TC ± 0.2 % f.s. RTD ± 0.1 % f.s.
Line resistance influence:
TC, mV <=0.4 uV/ Ω. RTD 3 wires 0.05%/ Ω (50 Ω balanced max.). RTD 4 wires 0.005%/ Ω (100 Ω balanced max.)
RTD excitation current:
Typical 0.350 mA.
CJC Comp.:
± 0.5°C.
Thermal drift (1):
Full scale ± 0.01% / °C. CJC ± 0.01% / °C.
Burnout values:
Max. value about 22.5 mA Min. value about 3.6 mA
Response time:
(10÷ 90%) About 400 ms.
Supply voltage:
10 …32 Vdc
Reverse polarity protection:
60 Vdc max.
Isolation:
Input – Power supply/Out 2000 Vac, 50 Hz,1 min.
Operative Temperature:
-40°C …+85°C.
Storage Temperature:
-40°C…+85°C
Humidity (not condensed):
0 …90 %.
Maximum Altitude:
2000 m.
Installation:
Indoor.
Category of installation:
II.
Pollution Degree:
2.
Material:
Self-extinguish plastic.
IP Code:
IP20.
Wiring:
Wires with diameter 0.8÷2.1 mm2 /AWG 14-18.
Tightening Torque:
0.8 Nm.
Mounting:
In compliance with DIN rail standard EN-50022 and EN-50035.
Weight About:
90 g.
Immunity:
EN 61000-6-2.
Emission:
EN 61000-6-4.
View AllClose