Information About Ultrasonic motor

An ultrasonic motor is a type of electric motor powered by the ultrasonic vibration of a component, the stator, placed against another component, the rotor or slider depending on the scheme of operation (rotation or linear translation). Ultrasonic motors differ from piezoelectric actuators in several ways, though both typically use some form of piezoelectric material, most often lead zirconate titanate and occasionally lithium niobate or other single-crystal materials. The most obvious difference is the use of resonance to amplify the vibration of the stator in contact with the rotor in ultrasonic motors. Ultrasonic motors also offer arbitrarily large rotation or sliding distances, while piezoelectric actuators are limited by the static strain that may be induced in the piezoelectric element. One common application of ultrasonic motors is in camera lenses where it, as part of the autofocus system, is used to move lens elements. It's replacing the noisier and often slower conventional micro-motor



Dry friction is often used in contact, and the ultrasonic vibration induced in the stator is used both to impart motion to the rotor and to modulate the frictional forces present at the interface. The friction modulation allows bulk motion of the rotor (i.e., for farther than one vibration cycle); without this modulation, ultrasonic motors would fail to operate. Two different ways are generally available to control the friction along the stator-rotor contact interface, traveling-wave vibration and standing-wave vibration. Some of the earliest versions of practical motors in the 1970s, by Sashida,[1] for example, used standing-wave vibration in combination with fins placed at an angle to the contact surface to form a motor, albeit one that rotated in a single direction. Later designs by Sashida and researchers at Matsushita, ALPS, and Canon made use of traveling-wave vibration to obtain bi-directional motion, and found that this arrangement offered better efficiency and less contact interface wear. An exceptionally high-torque 'hybrid transducer' ultrasonic motor uses circumferentially-poled and axially-poled piezoelectric elements together to combine axial and torsional vibration along the contact interface, representing a driving technique that lies somewhere between the standing and traveling-wave driving methods. A key observation in the study of ultrasonic motors is that the peak vibration that may be induced in structures occurs at a relatively constant vibration velocity regardless of frequency. The vibration velocity is simply the time derivative of the vibration displacement in a structure, and is not (directly) related to the speed of the wave propagation within a structure. Many engineering materials suitable for vibration permit a peak vibration velocity of around 1 m/s. At low frequencies — 50 Hz, say — a vibration velocity of 1 m/s in a woofer would give displacements of about 10 mm, which is visible. As the frequency is increased, the displacement decreases, and the acceleration increases. As the vibration becomes inaudible at 20 kHz or so, the vibration displacements are in the tens of micrometers, and motors have been built[2] that operate using 50 MHz surface acoustic wave (SAW) that have vibrations of only a few nanometers in magnitude.Such devices require care in construction to meet the necessary precision to make use of these motions within the stator. More generally, there are two types of motors, contact and non-contact, the latter of which is rare and requires a working fluid to transmit the ultrasonic vibrations of the stator toward the rotor. Most versions use air, such as some of the earliest versions by Dr. Hu Junhui.[3][4] Research in this area continues, particularly in near-field acoustic levitation for this sort of application.[5] (This is different from far-field acoustic levitation, which suspends the object at half to several wavelengths away from the vibrating object.)


Canon was one of the pioneers of the ultrasonic motor, and made the "USM" famous in the late 1980s by incorporating it into its autofocus lenses for the Canon EF lens mount. Numerous patents on ultrasonic motors have been filed by Canon, its chief lensmaking rival Nikon, and other industrial concerns since the early 1980s. Canon has not only included an ultrasonic motor (USM) in their DSLRs but also in the Bridge camera Canon PowerShot SX1 IS.[6] The ultrasonic motor is now used in many consumer and office electronics requiring precision rotations over long periods of time. The technology has been applied to photographic lenses by a variety of companies under different names:

Canon – USM, UltraSonic Motor

Minolta, Konica Minolta, Sony – SSM, SuperSonic Motor

Nikon – SWM, Silent Wave Motor

Olympus – SWD, Supersonic Wave Drive

Panasonic – XSM, Extra Silent Motor

Pentax – SDM, Silent Drive Motor

Sigma – HSM, Hyper Sonic Motor

Tamron - USD, Ultrasonic Silent Drive

Actuated Medical, Inc. - Direct Drive, MRI Compatible Ultrasonic Motor

20th Jan 2015 Information About Ultrasonic motor

Recent Posts